QLD Licence 90899 · Power point installations since 2016
Running out of power points? SEQ Sparky installs, replaces and upgrades power points across Brisbane Southside. Quality Clipsal and NHP products, neat cable runs and every point tested before we leave. Fully licensed, fully insured, quoted on site by Anthony.
Serving homes across Brisbane Southside, Logan, and Redlands.
You are running double adaptors and power boards in every room just to plug everything in. Overloaded outlets create heat buildup and increase the risk of electrical fires. Extra power points in the right spots eliminate the danger and the mess. If your switchboard is old it may also need upgrading to handle additional circuits.
Your power points have cracked face plates, discoloured plastic, loose plugs that fall out or switches that spark when you flick them. Damaged outlets are a shock and fire risk that should be replaced immediately. A safety switch will protect against earth faults but it cannot fix a physically damaged outlet.
You are renovating your kitchen, bathroom, outdoor area or adding a new room. Getting power points placed correctly during the build saves cutting into finished walls later. Plan your layout around where appliances and furniture will sit so you are not relying on extension leads after the job is done.
Working from home or setting up a shed workshop means you need dedicated circuits and enough outlets to run computers, monitors, tools and equipment without tripping breakers or overloading shared circuits. A dedicated circuit from the switchboard keeps your workspace running independently from the rest of the house.
The average Brisbane home built before 2000 has half the power points a modern household actually needs. More devices, more appliances, more demand.
Double adaptors and overloaded power boards are one of the leading causes of house fires in Australia. Purpose installed power points on properly rated circuits remove the risk entirely. No more daisy chaining boards behind the TV cabinet.
New flush mounted power points with clean white face plates make your walls look sharp. No more yellowed plastic, paint splattered covers or surface cracks from decades of use. A small upgrade that makes every room look better.
Getting power points where you actually need them means no more extension leads running across doorways or behind furniture. Kitchen benchtops, bedside tables, home offices and outdoor entertaining areas all benefit from outlets in the right spot.
Buyers and renters notice when a home has enough power points in practical locations. It is a small upgrade that makes a genuine difference when selling or leasing your property. Combined with a switchboard upgrade and safety switch installation it shows the electrics have been properly maintained.
Every quote is fixed in writing before work starts. No day-rate blowouts. No hidden materials charges.
1 new double power point installed
Up to 3 double power points installed
Up to 8 double power points replaced or installed
Final price depends on your home’s wiring, access and the number of points required. Anthony inspects on site and quotes in writing within 24 hours. Most power point installations are completed within a few hours.
Every Power Point Installation Brisbane homeowners book is completed to current AS/NZS 3000 standards and includes all of the following. No surcharges, no upsells on the day.
Australian made Clipsal and NHP power points and accessories. No cheap imports that crack and yellow within a year. Built to last in Brisbane conditions.
Before adding new power points we check the existing circuit capacity to make sure it can handle the extra load. If a new circuit is needed we let you know upfront with no surprises.
Whether surface mounted or chased into the wall, all cable runs are secured, clipped and finished to a professional standard. No loose cables hanging behind walls or running along skirting boards.
Every new power point is tested for correct polarity, earth integrity and insulation resistance before we leave. You get peace of mind knowing everything is wired correctly.
Anthony does the work personally. Not an apprentice. Not a subbie. Not a call centre dispatch.
Labour warranty on the install plus full manufacturer warranty on all Clipsal and NHP components fitted.
Anthony, Owner and Licensed Electrician · QLD Licence 90899
Simple, predictable, done in hours not days.
Call or fill out the quote form and tell us what you need. Extra power points in the kitchen, a full home upgrade, outdoor outlets or something specific for your workshop. Anthony will ask a few questions to understand the scope.
Anthony visits your home to check your switchboard capacity, existing wiring and the best locations for your new power points. You get a clear written quote with no surprises.
We install your new power points using quality Clipsal and NHP products. Everything is wired neatly, secured properly and connected to circuits with confirmed capacity. Anthony does the work himself.
We test every point for correct polarity and earth integrity, check your safety switches are covering the new circuits and walk you through what was done. You are left with a safe, tidy result and full confidence in the work.
Real power points, real homes, real results. Every job photographed on site.
Surface mounted power points installed on a block wall with circuit identification tags
Flush mounted power point on a kitchen splashback for a clean modern finish
Weatherproof outdoor power point and three phase outlet with NHP IP66 enclosure
Double power points installed inside a pantry cupboard keeping benchtops clutter free
We service Queenslanders, brick and tile, townhouses and newer builds. Every housing era Brisbane has.
Straight answers on cost, placement, compliance and what is actually involved.
A single double power point installation starts from $280 ex GST. The final price depends on whether it is surface or flush mounted, how far the cable run is from your switchboard and whether a new circuit is needed. We provide a clear written quote before starting any work.
Yes. We install power points in all types of Brisbane homes including older Queenslanders, post war homes and brick houses. Older homes sometimes need a new circuit run from the switchboard if the existing wiring is at capacity but we check all of this during the on-site assessment.
Flush mounted power points sit inside the wall with only the face plate visible. Surface mounted power points sit on the wall surface with a small box behind them. Flush mounting gives a cleaner look but requires cutting into the wall. Surface mounting is quicker and works well on brick, block and concrete walls.
Australian standards allow a maximum of 20 points on a single lighting and power circuit, but in practice we keep it well under that to avoid overloading. If you are adding several power points or running high draw appliances we may recommend a dedicated circuit from the switchboard.
Yes. Under Queensland electrical regulations all new power point circuits must be protected by a safety switch (RCD). If your switchboard does not have one covering the circuit we will recommend adding one as part of the installation.
Yes. We install weatherproof outdoor power points rated to IP53 or higher with spring loaded covers that keep moisture and dust out. Outdoor power points must be on their own RCD protected circuit and we handle all of that as part of the job.
Yes. We supply and install power points with built in USB-A and USB-C charging ports. They are great for kitchens, bedrooms and home offices where you are constantly charging phones and tablets without taking up a plug socket.
A single power point on an existing circuit typically takes 30 to 60 minutes. If a new circuit needs to be run from the switchboard or walls need to be chased it may take a bit longer. A full home upgrade with multiple points usually takes half a day.
For flush mounted power points yes we need to cut a small rectangular hole for the mounting box. We do this neatly with the right tools so the face plate covers the opening completely. For surface mounted points no cutting is required.
Yes. All electrical work carried out by SEQ Sparky comes with the appropriate testing and documentation to confirm it meets Australian standards and Queensland electrical safety regulations.
Fixed price quote within 24 hours. Most installations completed the same day. Call Anthony directly, no call centre, no middleman, no runaround.
Available Monday–Friday 7am–5pm · Emergency callouts available after-hours